![oya intime oya intime](https://static.latribune.fr/full_width/1079416/in-oya.jpg)
Awlcare is a non-yellowing sealer that will protect both Awlgrip and Awlcraft 2000 with regular applications. Traditional waxes which contain no abrasives probably do little harm to the coating, but offer no benefit.Īwlgrip has developed Awlcare Protective Polymer Sealer (73240) for those who want to enhance their finish and need the additional cleaning power of a hand applied, dry wash product. This creates the need to maintain the wax, increasing overall maintenance.
#OYA INTIME PLUS#
The residue can cause the topcoat to appear yellow, plus it attracts dirt. General: Traditional waxes break down rapidly. What You Should Not Do…ĭo not use traditional waxes. Use Awlcare to temporarily seal and restore gloss to painted surfaces dulled by age or mistreatment. Awlcare leaves a non-yellowing, protective polymer coating which lasts through multiple washings. It will remove mild stains, water spots and diesel soot while increasing resistance to attack from acid rain and other pollutants, when applied regularly. Awlcare is a hand applied, non-abrasive, synthetic polymer. Protecting the surface with Awlcare (73240) will help maintain the gloss of Awlgrip and Awlcraft 2000. Washing with Awlwash after use of vinegar is recommended. Use distilled white vinegar and hot water to remove stubborn salt stains.Latent solvent residue can attack the Awlgrip or Awlcraft 2000 Topcoat, while the wash down residue will attract dirt.
![oya intime oya intime](https://pharmalyon.com/52048-thickbox_default/inoya-mon-serum-anti-tache-30ml.jpg)
Always thoroughly rinse all surfaces with fresh water after cleaning with Awlwash or solvents.Use Awlcare (73240), by hand only, to remove stubborn diesel soot stains.After the use of solvents, wash these areas with Awlwash (73234) and water to remove any residue. Do not allow solvent to dry on the surface or puddle and soak into the surface. Apply cleaning solvents with soft clean cloths. When using solvents to remove stains, test an inconspicuous area first.AWL- PREP T0008, Awl-Prep 400-T0170, mineral spirits, xylene, and kerosene are acceptable for use on Awlcraft 2000. Use only milder solvents to remove stubborn stains. Solvents such as Awl-Prep-T0008, Awl-Prep Plus-T0115 (or T0340 Surface Cleaner in Europe), Awl-Prep 400-T0170, toluene, lacquer thinner, M.E.K., acetone, or kerosene may be used to soften or remove heavy build up of grease and grime, felt tip markings, or aerosol spray paint on the Awlgrip Topcoat. If water spots occur, they can be removed with Awlcare Protective Polymer Sealer (73240).Wiping the surface dry with a chamois or soft cotton towel is recommended. A water softener is recommended to eliminate hard water residue. Thoroughly rinse all surfaces with fresh water after washing to remove all detergent residue.Use soft, non-abrasive cloths, sponges or washing mits when washing. When washing it is important to keep the surface wet to prevent Awlwash from drying on the surface.When using Awlwash, it is important to dilute as specified on the label. Some “marine soaps” are not suitable for use on painted surfaces. Awlwash does not contain alkalies, acids, or abrasives. Wash the surface regularly with fresh water and Awlwash Wash Down Concentrate (73234) which is formulated to clean Awlgrip and Awlcraft 2000 topcoats.This premature aging can cause the finish to appear dull. Regular Cleaning will avoid build of dirt, grease and other contaminants which can slowly cause premature aging of Awlgrip or Awlcraft 2000.If you follow the manufacturer’s recommendation, you should get years of service from your finish. When you apply an Awlgrip finish to your boat, do not consider it to be a no-maintenance finish, but rather a low-maintenance finish. Awlgrip Cleaning and Maintenance for a Long Life Finish What You Should Do…